Yield Optimisation

Ad yield optimisation: more revenue from the traffic you have

Ad yield optimisation means earning more from every visit to your site, not filling more ad slots. Fusion raises yield with AI dynamic floors, header bidding with bid throttling and ads that only load and refresh in view, then proves each change with A/B experiments on live traffic and shows which SSPs earn their place.

Yield vs fill

Why a full ad slot isn't always the best-paid one

Selling every impression at any price fills the page but lowers what each visit earns. A yield-led set-up prices each impression on its merits.

Comparison of a fill-led ad set-up and a yield-led set-up in Fusion
AreaFill-led set-upYield-led, with Fusion
GoalAn ad in every slotThe most revenue per visitor
Floor pricesKept low so everything sellsSet daily per ad config by AI Dynamic Floors
Unsold impressionsAvoided at almost any priceBackfilled with your own creatives to recirculate users
When ads loadOften on page load, in or out of viewOnly when the unit is in view, and refreshed only in view
Measured byFill rate and impressionsRPM per user and session, viewability and latency
How it works

The yield loop: measure, test, keep the winner

  1. 01
    Measure
    SSP Insights, benchmarking and Revenue Analytics show where yield is being lost: weak bidders, slow auctions, low-value traffic.
  2. 02
    Test
    Set up a variant ad config and run an experiment on a share of live traffic. Fusion reports RPM, revenue, viewability, fill, latency and bid rates for each.
  3. 03
    Activate the winner
    One click switches the winning config on and the losing ones off. Your tag is rebuilt and live within 10 minutes.
Experiments

What you can test on live traffic

Variant configs don't need to be switched on. Fusion enables them for the share of traffic in the test and leaves everyone else on your current set-up.

Examples of yield experiments in Fusion and the metrics to watch
What to testExampleWhat to watch
Ad format and placementIn-image ads shown "in" the image vs "under" itExperiment RPM, viewability
Page layoutTwo MPUs spaced out vs one double MPUExperiment RPM, viewability, fill
Floor pricesAI Dynamic Floors vs your current floorsExperiment RPM, fill
Header biddingFewer SSPs, bid throttling settings or a shorter timeoutBid rate, ad latency, experiment RPM

Not sure where to start? A free healthcheck reviews your header bidding, SSP count, Prebid timeout and ads.txt, and shows where yield is being lost.

FAQ

Ad yield optimisation questions, answered

What is ad yield optimisation?
Ad yield optimisation is the work of earning more revenue from the same traffic: raising the value of each impression and each visit (RPM) rather than showing more ads. For publishers it covers floor prices, header bidding demand, ad layout and formats, viewability and page speed, tested and measured over time.
What is the difference between yield and fill rate?
Fill rate is the share of ad requests that return an ad. Yield is how much those ads earn. Higher floors can lower fill but raise overall revenue, because impressions that do sell go for a better price. Fusion optimises for yield; if you would rather not show blank slots, you can supply backfill creatives that serve when a slot is not monetised.
What is yield management in advertising?
Yield management in advertising is selling ad inventory at the best price it can command: setting floor prices, choosing demand partners, and deciding where and when ads appear. It borrows the idea from airlines and hotels, which price the same seat or room differently depending on demand.
How does Fusion pick the winner of an experiment?
Fusion compares the configs in an experiment on experiment RPM, the revenue per 1,000 times each config was served. The report also shows revenue, viewability, fill, latency and bid rates, so if those matter to you, review them before you activate the winner.
How many SSPs should I run in header bidding?
Enough for competition, but not so many that latency rises and returns diminish. More SSPs can lift CPMs and fill; too few limits competition. Fusion's bid throttling removes underperforming SSPs from the auction for each user in real time, and SSP Insights shows which partners are worth keeping.
Will optimising yield slow my site down?
It shouldn't. Fusion only loads and refreshes ad units when they are in view, and experiment reports include ad latency so you can see the effect of a change before rolling it out. See Core Web Vitals for how the tag protects page speed.
Can I optimise yield on my own Google Ad Manager?
Yes. Floors, header bidding, experiments and reporting work with your own Google Ad Manager (Self-Service) or ours (Plug & Play and Managed Service). On the Managed Service, our ad ops team runs the testing for you. See Google Ad Manager.
How quickly do changes go live?
Changes made in Fusion are pushed to your live tag without a site deploy. When you activate an experiment winner, your Publisher Tag is rebuilt and deployed within 10 minutes. Dynamic floor traffic changes take effect at the next midnight UTC.

Find out where your yield is leaking.

Get a free revenue healthcheck, or sign up and run your first experiment on live traffic.